Dave K Posted April 21, 2005 Posted April 21, 2005 << Is Dave working hard again , he has not been on for sometime.... >> lol, aye waiting for hard drives to sort the hotel server. 2 weekends cancelled now expecting to do a re-install to then have it all go out the window at last minute. Suppose to be doing it this weekend now but could end up being next weekend, can?t organise nowt. Andi, if am off I'll sort fitting the sensor.
andy_bray Posted April 21, 2005 Posted April 21, 2005 << Suppose to be doing it this weekend now but could end up being next weekend, can?t organise nowt. Andi, if am off I'll sort fitting the sensor. >> Dave dude , there is no rush M8 ....
andy_bray Posted April 21, 2005 Posted April 21, 2005 Good morning all DUDEs...... Not long now Richard...
Jimmy Mc Posted April 21, 2005 Posted April 21, 2005 Afternoon dudes! Off to the gym soon. Sweeeeeeet! Finally found someone reliable to train with.
Cret Posted April 22, 2005 Posted April 22, 2005 GT4 - world championship dude.... Oh and pulling apart the rear shock off my bike. Should be getting put together anytime soon then in for its test.......
andy_bray Posted April 22, 2005 Posted April 22, 2005 Good morning dudes ,, Iam painting tthe walls in my house today I want to go for a drive in my car... Well off to B&Q Then....
heazille Posted April 22, 2005 Posted April 22, 2005 << Iam painting the walls in my house today I want to go for a drive in my car... >> Guess which of those two WE are doing Ta Ta Heazille Towers have gone on Tour
andy_bray Posted April 23, 2005 Posted April 23, 2005 Painting done dudes.... I have a viewing on my house tomorrow ,,,Fingers crossed...
andy_bray Posted April 23, 2005 Posted April 23, 2005 Sweeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeet afternoon dudes..
Cret Posted April 23, 2005 Posted April 23, 2005 Certainly is dude!! Got my new chain & sprockets for the bike today. That's all the bits I need now hopefully and just got both new tyres on too. Can start putting it all back together now and apply for its test.....
Dave K Posted April 23, 2005 Posted April 23, 2005 Sweet Jim, just in time for TT. Hope you dont make to much mess in the kitchen!
Dave K Posted April 23, 2005 Posted April 23, 2005 Project Tart continues dudes. Fitted oil catch can as was getting way to much oil in inlet tract. Cant have the car running on 2 stroke. Catch Can Also pulled the new power cable through the bulk head for me new amp/sub setup. Power Cable And due to the bigger cable I need to install a slightly bigger fuse.! Fuse
Cret Posted April 24, 2005 Posted April 24, 2005 That catch can is hella tasty Dave - good work!! That cable is a bit mad though! Bike is outside the house now as there's not enough room in the kitchen. Got both new tyres on today, front wheel back on & front brake calipers on. Swingarm removed, taken to bare metal, primed & sprayed, and shock/spring stripped down, and cleaned/painted reaassembled. Quite a bit done now and it can all go back together. Still has to go through its test after that though.
Dave K Posted April 24, 2005 Posted April 24, 2005 << That catch can is hella tasty Dave - good work!! That cable is a bit mad though! Bike is outside the house now as there's not enough room in the kitchen. Got both new tyres on today, front wheel back on & front brake calipers on. Swingarm removed, taken to bare metal, primed & sprayed, and shock/spring stripped down, and cleaned/painted reaassembled. Quite a bit done now and it can all go back together. Still has to go through its test after that though. >> Cheers Jim, not bad for $480 hey and 304 stainless steel too. I know, I tried to get a 2 gauge kit but could'nt find one at a reasonable cost so had to buy overkill 0 gauge to cover 1600watts! (Peak) I?m sure it will pass dude. PS Hong Kong Dollars so it only cost £32. lol
Dave K Posted April 24, 2005 Posted April 24, 2005 Think I should start a new thread with this lot. My e-bay bargain turned up yesterday, so I stripped it last night in preparation for a bit of diy porting and polishing. In a bit of a mess. Inlet 1 Ingnition leads, coil pack and idle control valve removed. Inlet 2 The mess of fuel pipes that will be removed and replaced with a parallel fuel setup. Inlet 3 Fuel rails, injectors and air inlet removed. Inlet 4 Inlet 5 Inlet 6 And the poor casting finish that am hoping to remove. Inlet 7 And a quick clean with a wire brush. Inlet 8 Inlet 9 Tune in next week for more of Dodgy Daves Diy!. lol
Cret Posted April 24, 2005 Posted April 24, 2005 1600?! If that's peak what is it in real watts (ie RMS)? That's way cheap for that catch can - bloody bargain!! Waht's with the manifold though Dave, is it some fancy one or just a spare standard one? I've got a spare normal one I could have given you dude!
andy_bray Posted April 24, 2005 Posted April 24, 2005 Been a nice day dudes been out in the STI Nick dude you want to clean that bird cr@p off your scooby M8... Any news on Richards new car ??? and what is it ....
paul n Posted April 25, 2005 Posted April 25, 2005 << Any news on Richards new car ??? and what is it .... >> Seen it looks
andy_bray Posted April 25, 2005 Posted April 25, 2005 << << Any news on Richards new car ??? and what is it .... >> Seen it looks >> It looks SWEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEET Paul dude....
andy_bray Posted April 25, 2005 Posted April 25, 2005 Good morning dudes ...................Sweet day.....
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now